NEWS
Hydraulic Lift Platforms: Maintenance and Servicing of Hydraulic Lift Platform Machinery and Equipment
1. The braking systems of all components of the hydraulic lifting platform should be regularly inspected and adjusted on a periodic basis. Specifically, the clearance between the brake pads and brake wheels must be checked and adjusted to ensure flexibility and reliability. There should be no debris present on the friction surfaces; if debris is found, it must be removed using gasoline or a solvent.
2. The lubrication of each component, including reducers, gearboxes, and external gear transmission gears, as well as the gear oil used, shall be carried out in accordance with the specifications outlined in the lubrication chart.

3. For hydraulic lifting platform machinery and equipment, pay close attention to checking whether the galvanized steel wire ropes at various locations have any broken wires or loose strands. If these conditions exceed the relevant requirements, they must be replaced immediately.
4. Hydraulic lifting platform machinery and equipment should be regularly inspected for connection conditions at all joints. If any looseness is detected, the connections should be tightened immediately. The bolts connecting the body to the base should be checked for tightness when the body is under load (a rotating arm can be used to simulate the loading condition). All connecting pin shafts must be fitted with cotter pins, which must be fully spread open.
5. Regularly check whether all components are operating normally and whether there are any unusual noises. If any common faults are detected, they must be addressed immediately.
6. When installing, disassembling, and adjusting the rotating assembly, be sure to ensure that the centerline of the rotating assembly’s reducer is parallel to the centerline of the transmission gear, with a meshing area of at least 70 percent and an appropriately sized meshing clearance.
7. Regularly inspect all cables and wires on hydraulic lifting platform machinery equipment for any damage. Promptly secure and replace any damaged sections.
8. If the motor overheats, stop it immediately, troubleshoot the issue, and then resume operation only after the fault has been resolved. The motor bearings must be well-lubricated.
9. Each carbon brush section must have a clean surface, and the working pressure of the carbon brushes should be adjusted so that the contact area is no less than 50 percent.
10. Regularly keep clean all control cabinets, distribution cabinets, and other equipment on the hydraulic lifting platform, and promptly remove dust from electrical devices.
11. The contact points of the limit switches for all safety devices on the hydraulic lifting platform must be reliably actuated, and any arc pits on the contact points should be polished immediately.
Relevant information
COOKIES
Our website uses cookies and similar technologies to personalize the advertising shown to you and to help you get the best experience on our website. For more information, see our Privacy & Cookie Policy
COOKIES
Our website uses cookies and similar technologies to personalize the advertising shown to you and to help you get the best experience on our website. For more information, see our Privacy & Cookie Policy
These cookies are necessary for basic functions such as payment. Standard cookies cannot be turned off and do not store any of your information.
These cookies collect information, such as how many people are using our site or which pages are popular, to help us improve the customer experience. Turning these cookies off will mean we can't collect information to improve your experience.
These cookies enable the website to provide enhanced functionality and personalization. They may be set by us or by third-party providers whose services we have added to our pages. If you do not allow these cookies, some or all of these services may not function properly.
These cookies help us understand what you are interested in so that we can show you relevant advertising on other websites. Turning these cookies off will mean we are unable to show you any personalized advertising.
Service is endless.
We look forward to serving you.
If you have any questions, please leave your information.
XiongHao Machinery Technology(XiangShan) Co.,Ltd.
Address: Xizetang Industrial Zone, Xianxiang Town, Xiangshan County, Zhejiang Province
Contact Information
Phone:+86-15867878936 +86-574-88079868
Email:wang@nbxhmachinery.com
Copyright © XiongHao Machinery Technology(XiangShan) Co.,Ltd. All rights reserved Powered by www.300.cn SEO
QR code